Terra Cotta Restoration Products - Edison Coatings, Inc.

RL-Series Restoration Latexes RL-1, RL-2, RL-3, RL-4, RL-5, RL-6
RL-Series latex modifiers are unique reactive acrylic additives designed to enhance the performance of Portland cement based materials. When added to Portland cement based mortars, patches, plasters and coatings, RL-Series latex modifiers improve mechanical performance, workability, adhesion and resistance to harsh environmental exposures.

Custom SYSTEM 45 Masonry Repair & Coating Compounds
Edison Custom SYSTEM 45 products are two-component, latex-modified, cementitious compounds used to produce highly durable and compatible aesthetic repairs to masonry and concrete.

SPEC-JOINT 46 Custom Masonry Repointing Mortar
SPEC-JOINT 46 is a series of pre-colored, prepackaged, lime and cement-lime mortars for use in new construction and restoration. Lime mortar is formulated to match traditional historic mortars, and cement-lime mortars are formulated in accordance with ASTM C-270 specifications to provide consistent, reliable results in both performance and appearance. SPEC-JOINT 46 is simply mixed with water prior to use, and is applied in accordance with Standard Procedures for use of masonry mortar.

SYSTEM 49 CPBA Corrosion Resistant Primer and Bonding Agent for Embedded Reinforcing Steel
SYSTEM 49-CPBA is a two-component, latex-cement primer and bonding agent designed to protect steel reinforcement from corrosion while promoting adhesion between patching compounds and concrete and steel substrates.

PUMP-X 53, 53i, 53iE, 53iL Pumpable Cementitious Grouts
PUMP-X53 is a multi-purpose, low modulus, moderate strength filler used for filling cavities, voids and cracks from a minimum of ¼" width up to approximately 18 inches.
PUMP-X53i is an ultra-fine, moderate strength micro-injection grout which achieves high flow for efficient filling of small cracks and voids from a minimum width of approximately 1 mm to as much as several inches in thickness.
Pump-X 53iE is an ultra-fine, expanding, non-polymer cementitious injection grout designed for filling small cracks and voids in sound concrete and masonry construction. Slight expansion after placement and before final set enables the material to force itself into close, positive contact with internal crack surfaces, where desired.
PUMP-X-53iL is a softer, non-polymer, hydraulic lime grout, for use in Historic masonry restorations requiring repairs to lower strength brick and softer stone elements.

THIN-FILL 55 Masonry & Concrete Thin-Section Reprofiling Mortar
THIN-FILL 55 is a latex-modified reprofiling mortar for application of thin-section patches of 1/32 to 1/4 inch depth while maintaining excellent adhesion, strength, breathability and resistance to cracking.THIN-FILL 55 provides smooth finishes which can also be further polished to repair glazed terra cotta or polished stone profiles.

SILOX-TREAT 89W, WH
Waterborne, reactive silane-siloxane water repellents reduce water absorption in porous substrates without affecting permeability or appearance.

SYSTEM 90-II, 90-W Catalytic Breathing Sealers & Stains
Edison SYSTEM 90-Series sealers are reactive treatments designed for maximum performance and exterior durability in protection of on-grade and above-grade stone, concrete and masonry. Surfaces treated with SYSTEM 90 products are sealed against a wide range of chemical and weather exposures, including acid rain, melting snow, freeze-thaw, de-icing salts, air pollutants, wind driven rain and a variety of other materials.Pigmented treatments combine all the performance of 90-Series sealers with the aesthetic benefits of a durable semi-transparent stain.

LiquiDirt 94 Sealer, Stain & Faux Finish
LiquiDirt 94 is a durable, high-permeability stain and faux finishing treatment designed for application to on-grade and above-grade stone, masonry, mortars, stucco and concrete. It is used for"aging" of new masonry replacements or repairs, to change color of new or existing masonry units, or to overcome fading or staining in original materials.

AQUATHANE UA-210 Types E, F, NCL and H-A/G Waterborne Polyurethane Coatings
EDISON AQUATHANE UA-210 products are multi-purpose, high-performance, waterborne polyurethane- based coatings which can be applied to natural stone. They are breathing, low in odor, VOC-Compliant, fast drying, reactive, single component products. Cured films are tough, flexible, and resistant to abrasion and intermittent exposure to water and many chemicals.

AQUASPEX 220 Multi-Colored Special Effects Coatings
AQUA-SPEX 220 is a specialty coating system designed to provide multi-color finishes in a single, simple application. They are based on clear, high-performance, highly durable, water-borne polyurethane coatings into which color specks of varying sizes and colors have been dispersed. The coating can be used to simulate multi-colored granite and marble.

EVERKOTE 300 Mineral Coatings & Stains
EverKote 300 coatings are waterborne inorganic paints and stains based on potassium silicate binders. Potassium silicate masonry paints have been in use for over a century to provide extremely durable, breathable color coatings on all types of mineralbased substrates, including stone, masonry, concrete and cement plaster (stucco).Two standard grades of are available: Penetral Low Viscosity, SemiTransparent Stains and Patinar Medium Viscosity, Opaque Coatings

PRIMER #342 for waterborne coatings.
Primer 342 is a low viscosity, vapor permeable acrylic emulsion primer. It is used for penetrating and conditioning porous or friable surfaces prior to coating with Elastowall 351 breathable masonry coatings. It has also been used as a pre-treatment for aiding in the drying out of deeply saturated, thick section concrete and masonry structures.

ELASTO-WALL 351 and ELASTO-TONE 353 Breathable Elastomeric Masonry Coatings
ELASTO WALL 351 is a permanently flexible breathable masonry coating designed to waterproof and decorate vertical and sloped above-grade surfaces, including all types of natural stone, and including walls exhibiting small working cracks. It has higher vapor permeability than some mineral coating products, and can be applied over a wide variety of previous coatings and treatments.
ELASTO-TONE 353 is a highly permeable finish system for economical color coatings and "touch-up" applications. Based on the same chemistry as ELASTO WALL 351, it features high elongation and low temperature flexibility, while offering greater economy, due to lower build and higher application rate.

FLEXI-WELD 520, 520T Epoxy Adhesives
FLEXI-WELD 520 and 520-T are two-component, moisture insensitive, high strength 100% solids epoxy adhesives for general purpose bonding to a wide variety of substrates, including stone, masonry and dry or damp concrete.

FLEXI-FILL 530 Epoxy Filler
FLEXI-FILL 530 is a unique two-component, slightly flexibilized 100% solids epoxy-acrylate-isocyanate terpolymer adhesive for surface-sealing cracks and filling small depressions in a wide variety of substrates. Suitable substrates include terra cotta, concrete, masonry and stone. FLEXI-FILL 530 is a paste adhesive, which should be used neat or mixed with coarse fillers and tooled onto bonding surfaces. Although it is packaged in premeasured "A" (Resin) and "B" (Hardener) components, the mix ratio is far less critical than for traditional 2-part epoxy formulations. This allows the user to adjust working consistency at different temperatures. This variable ratio feature makes FLEXI-FILL 530 a true "all season" epoxy adhesive and sealant.

Back To Top

3 Northwest Drive, Plainville, CT 06062 USA

Phone: (860) 747-2220 or (800) 341-6621

FAX: (860) 747-2280 or (866) 658-1189

E-Mail: Contact Us


	EDISON COATINGS PRODUCTS ARE FOR COMMERCIAL & INDUSTRIAL USE ONLY

Last Updated:

Tuesday, May 06, 2008



	Society for the Preservation of Historic Cements, Inc.

LIMITS OF LIABILITY

Edison Coatings, Inc. makes no warranties, express or implied, as to the accuracy or completeness of any of the information contained herein. This publication is offered on a complimentary basis as a service to potential customers or specifiers. While every effort has been made to include complete and accurate information, based on data and information believed to be reliable, it is the sole responsibility of the user to determine its suitability for his own intended use and purposes. Nothing contained herein shall be construed as a warranty or guarantee of any product, process or any other recommendation stated herein. Edison Coatings, Inc. assumes no responsibility for advice given, results obtained, or for any damages whether incidental or consequential, which may be incurred as a direct or indirect result of the use of this information. By proceeding to use this information, user acknowledges and agrees that he is doing so at his own risk, and user indemnifies and holds Edison Coatings harmless against any liabilities, costs or expenses resulting therefrom. All product sales are further governed by the Edison Coatings, Inc. CONDITIONS OF SALE.